HT7248FFi
540 Line Color Dome Camera
Intensifier Series, Focus Free
Wall & Ceiling Mountable
Please read this manual thoroughly before operation and keep
it handy for further reference.
Contents
Package Contents
3
Precautions
4
Camera Installation
Features
5~8
9~10
OSD Setting
Troubleshooting
Specification
Dimensions
Warranty
11~16
17~18
19
20
21
2
PACKAGE CONTENTS
•
Please make sure that the following items are included
in the package:
1 HT7248FFi Camera
2 Mounting Screws
1 Chameleon Dome Cover
1 Video Test Cable
Please leave this manual with the end-user for future
reference.
3
PRECAUTIONS
•
•
THIS DOME CAMERA SHOULD BE ONLY INSTALLED BY
QUALIFIED PERSONNEL
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE. THE DOME COVER SHOULD BE
TREATED WITH CARE
•
•
DO NOT CELAN THE COVER WITH AN ABRAISIVE CLEANING
MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO
CLEAN THE DOME COVER
THERE ARE NO USER-SERVICEABLE PARTS INSIDE.
PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN
TO MAKE INITIAL ADJUSTMENTS
•
•
•
•
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
12 VOLT DC POWER SUPPLY
PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
4
CAMERA INSTALLATION
1. CONNECT POWER CABLE
1) WHEN USING 12 VOLTS DC (constant voltage 600 mA)
-CONNECT ACCESSORY CABLE TO THE CABLE LEAD
OF THE CAMERA AND CONNECT 12V DC POWER SUPPLY.
POWER INPUT:RED
CONNECT
CENTER:(+)
POWER SUPPLY
2) WHEN USING 24 VOLTS AC (40 Volt Amps)
CAMERA
RED(+)
CONNECT
AC 24V
BLACK:(-)
POWER SUPPLY
3) CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
YELLOW:VIDEO OUT
4) CONNECT RS-485 CABLE
-CONNECT 2WIRE CABLE TO THE 485PORT AS BELOW.
5
CAMERA INSTALLATION
2. CHAMELEON COVER INSTALLATION
1) If you wish to change the color of the HT-7248FFi,
place the Chameleon Dome over the camera
Place the Chameleon Dome over the HT-7248FFi and push until
it snaps into position.
● Notes : Optional painting before installation
* Painting method for the Chameleon Dome
* Spray the color of your choice onto the Chameleon cover
* If necessary, apply a second coat
6
CAMERA INSTALLATION
3. CONTROL BOARD
1
2
3
4
1) Video Test Terminal
For second video output
2) OSD (On Screen Display) Joy stick
Press the Joy stick for one second until the OSD menu tree
appears on the screen. Move the Joy Stick up, down, left &
right to control the OSD functions.
3) DIP Switch setting for RS485
Please see the next page for controlling this switch.
4) Lens adjustment (for Zoom) Joy stick
Adjust the Joy stick left or right to control between TELE &
WIDE, Focus is automatically matched without any adjustment.
7
CAMERA INSTALLATION
4. DIP Switch Setting for RS-485 (Pelco-D)
1
2
3
4
5
6
1) Address Setting
to set Camera Address, place switches based on below chart.
2) Baud rate Setting
to set Baud rate, please refer the chart below.
8
Features
SLC
When the image is in front of strong background lighting,
your camera allows you to get a clear image.
INTENSIFIER
1/3 inch density CCD and digital processor permit high quality
pictures to be captured in very low light condition.
High Resolution
Horizontal resolution of 540 TV lines is achieved by using a
SONY Double Speed CCD with 410,000 pixels, yielding pictures
with a high S/N ratio..
Motion Detection
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
9
OSD
All camera functions are menu driven for easy use.
Dynamic Noise Reduction
The Intensifier camera has a DSP chip that can remove image
noise efficiently showing clean images in low light conditions.
ELECTRONIC DAY/NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
MANUAL / AUTO IRIS LENS
The Intensifier camera will work with auto iris, manual iris and
fixed iris lenses.
10
Operating your camera
OSD Function
SETUP MENU
LENS TYPE
● DC IRIS
SHUTTER TYFE
● ELC
● FIXED ● MANUAL
WHITE BALANCE
● ATE
● AWC
● MANUAL
SLC
● HIGH ● MIDDLE ● LOW ● OFF
AUTO GAIN
● HIGH ● MIDDEL ● LOW ● OFF
REDUCE NOISE
● HIGH ● MIDDLE ● LOW ● OFF
INTENSI FIER
● AUTO ● OFF
NEXT PAGE
● CAMERA TITLE ● DAY/NIGHT ● SYNC
● MOTION
● PRIVACY
● REVERSE
● DETAIL
● DEFAULT
● PAGE1
EXIT
11
SETUP Menu Functions
1. LENS (DC) – Lens is static with DC auto iris lens only
2. SHUTTER (Option : OFF / FLK / MANUAL/ ESC)
Flickerless mode (FLK) reduces on-screen flickering.
Electronic Shutter Control (ESC) adjusts brightness level
on screen.
Manual mode allows you to adjust the shutter speed from
1/60~1/120,000 of a second (NTSC).
3. WHITE BAL. (Option : ATW / MANUAL / AWC)
Select Auto Tracking White Balance (ATW) when the color
temp. is 2400°K~12000°K.
Manual mode allows you to increase or decrease the red
or blue factor on screen.
Auto White Balance Control (AWC) automatically adjusts
the white balance to your specific environment.
4. SLC (Speco Light Compensation) - BACKLIGHT
It provides intelligent light level control to overcome severe
Backlight conditions by Low, Middle & High level control.
12
5. Auto Gain ( Low / Middle / High)
Increase the GAIN level to brighten the picture.
(noise / distortion may develop)
6. REDUCE NOISE (Low / Middle / High)
Reduces noise/distortion on the screen, Increasing the
REDUCE NOISE level reduces noise but may introduce video
Artifacts, it is deactivated if AGC is turned off.
7. INTENSIFIER
Automatically provides a clear image under low-light
conditions. You can control the maximum low-light
magnification from 2x to 128x, It is deactivated when
SHUTTER is set to FLK mode.
8. NEXT PAGE
Takes you to the special functions.
9. EXIT
Exits the SETUP menu and returns to video monitoring.
13
NEXT PAGE Menu Functions
1. CAMERA ID
UP, DOWN, LEFT, RIGHT menu control = Select a
character, then press (SETUP)MENU to accept it.
The character is saved and the title cursor at the bottom of the
screen moves to the next position.
← → = Go back or forward in the title name to make changes.
CLR = Delete the entire name and start again.
POS = Position the camera title on the screen.
Press (SETUP)MENU to confirm the position.
END = Accept the new name.
2. COLOR (Auto / On)
Sets the camera to either automatic color/black and white or
full-time color mode.
* Auto : The camera will switch into B/W mode under low light
conditions.
* Color : Always display a color picture.
OSD Key may not work for 3 seconds when COLOR/ BW
mode is changed
14
3. SYNC (INT / Line Lock)
INT : When line lock is not required.
It synchronize the vertical interval sync pulse of your
camera with other equipment to reduce the effect of
picture roll on the monitor.
L/L : Adjust the vertical phase (VPH) from 000 ~ 359
Line Lock is only available with 24VAC power.
4. MOTION
Detects moving objects on screen and displays MOTION
DETECTED along with the number of movements counted.
Allows you to select the area on screen you want to observe.
AREA SEL = Select a motion detection grid (top left, top
right, bottom left, bottom right) to modify.
AREA STATE = Activate or deactivate the selected grid.
TOP/DOWN/ = Press LEFT or RIGHT menu control left or
LEFT/RIGHT right to alter the dimensions of the selected
grid.
15
5. PRIVACY
Allows you to mask certain areas of the screen from
observation
AREA SEL = Select a motion detection grid (top left, top
right, bottom left, bottom right) to modify.
AREA STATE = Activate or deactivate the selected grid.
TOP/DOWN/ = Press LEFT or RIGHT menu control left or
LEFT/RIGHT right to alter the dimensions of the selected
grid.
6. MIRROR
Produces a horizontal mirror image on screen.
7. SHARPNESS
Sharpens the image on screen. You can adjust the sharpness
Level from 0~31 (excessive sharpening may cause picture
noise to develop).
8. RESET
Restores all factory default settings.
9. RETURN
Returns to the main SETUP menu.
16
Troubleshooting
If you have trouble operating your camera, refer to the following
Problem
Solution
Nothing appears on
the screen.
● Check that the power cord and line connection
between the camera and monitor are proper
● Check that you have properly connected VIDEO
cable the camera VIDEO output jack.
The image on the
screen is dim.
● Is lens stained with dirt? Clean your lens with
soft,
clean cloth.
● Set the monitor to proper condition.
● If the camera is exposed to too strong light
change the camera position.
● Adjust the lens’ focus properly.
● Adjust the contrast feature of the monitor.
The image on the
screen is dark.
● If you have an intermediate device, set the
75Ω/Hi-z properly.
The camera is not
working properly, and
the surface of the
camera is not.
● Check that you have properly connected
the camera to an appropriate power source.
● Have you set ‘MOTION DET.’ menu to off?
● Have you set ‘MD LEVEL’ to too how?
● Have you set ‘MD ARAEA’ properly
MOTION
DETECTION
function is not active.
17
Problem
Solution
The color of the
picture is not
matched.
● Check that you have properly set the
‘ WHITE BALANCE ’ menu
The image on the
screen flickers.
● Is the camera facing to direct sunlight or
fluorescent
lighting? Change the camera position.
L/L mode isn’t able
to be selected.
● Have you connected your camera to DC power
source? Connect it to AC power source.
18
SPECIFICATIONS
ITEM
HT – 7248FFi
Power Source
Power Consumption
Image Sensor
Total Pixels
12VDC & 24VAC ( Dual Voltage )
500mA (DC) / 6.6W (AC)
1/3”, SONY SUPER HAD CCD, 410,000 pixels
811(H) x 508(V) , 1/3” CCD
768(H) x 494(V) , 1/3” CCD
Focus Free Lens 3.5~10mm
1 : 1.3 ~2.0
Effective Pixels
LENS TYPE
Maximum Aperture Ratio
Scanning System
2 : 1 Interlaced 525 Lines / 60 Fields / 30
Frames
Synchronization
Internal / Line Lock selectable
1.0V [p-p] Composite, 75Ω
540 TV Line
Video Output
Resolution
Gain Control
AGC-L, AGC-M, AGC-H, OFF selectable
1/60 ~ 1/200,000 sec
Electric Shutter Speed
INTENSIFIER
Built-in ( selectable limit ~ X128)
W-ATW / S-ATW / AWC /MANUAL
0.002Lux (intensifier) 0.3Lux (shutter)
50dB (Weight On)
WHITE BALANCE
Min. Illumination
S/N ( Y signal)
Reduction Noise
Motion Detection
On Screen Display ( O.S.D )
PRIVACY Function
Operational Temperature
Operational Humidity
OFF / LOW / MIDDLE / HIGH
MD1 / MD2 / OFF
Built – in
ON / OFF (4 Programmable Zone)
-29℃ ~ +50℃ ( - 20℉ ~122℉)
30% ~90% RH
19
DIMENSIONS
* SIDE VIEW
* TOP VIEW
20
WARRANTY
21
MEMO
200 New Highway
Amityville, NY 11701
631-957-8700
VER. 080901
This manual is based on the date as shown in the right and specifications are subject to
Change without notice for quality improvement.
|